Pneumatic silencers
The modern standards of labor protection require quite strong norms of noise at work places. So, pneumatic compressors need to be equipped by good mufflers to reduce the noise. ALUPOR™ offers cheap effective solutions with low flow resistance:
Silencer for pneumatic automation systems and compressed air tools with pressure up to 10 bar.
ANALOGUES:
Camozzi 2921 Series
Camozzi 2931 Series
FESTO AMTE Series
AVENTICS Sl1 Series
SMC AN Series
Silensers for high pressure air discharges taking place at PET bottles production etc.
ANALOGUES:
Festo U-G1-HD-SA
SMC VCHN Series
Silensers for Ingersoll Rend pneumatic (air) motors and other tools like srcewdrivers and pneumatic jackhammers.
ALUPOR™ performs exceptionally well alongside sintered materials for exhaust noise silencing. Moreover, silencers made of porous aluminum function perfectly under cryogenic temperatures maintaining their strength properties. Exhaust noise can occur in various technological processes involving pneumatic and compressor equipment. Technological equipment that assumes gas discharge have to be equipped with silencers to protect the environment and production personnel from the harmful effects of noise. Currently, the company offers several series of commercially produced silencers.
Advantages
- Increased strength and durability compared to silencers made of sintered powders
- Resistance to cyclic and vibration loads
- Resistance to contaminants — maintains flow capacity for extended periods even in dusty air
- High dirt-holding capacity due to unique structure
- Fully controlled and stable structural parameters
- Durability: maximum pressure differential up to 50 atm (under normal conditions)
- Any sizes and configurations available
- Parts combining solid and porous sections in a single product
- Thread cutting possible on both solid metal and porous sections
- Low weight - only plastic is a competitor
- Service life exceeding 5 years
- Environmentally friendly — material can be recycled as aluminum scrap
Limitations
- Icing (fair for any porous silencer): when designing silencers, it should be considered that the discharged medium is throttling through the porous structure. Its temperature may drop below the crystallization point of the water. Ice formation on the silencer can reduce or completely block the flow. In such conditions, heating is required.
- On large silencers, noise may be generated inside the silencer itself: it is necessary to provide additional distribution elements made of coarse-porous material at the outlet of the pipe for preliminary jet breaking.
SPECIFICATIONS
FLOW PARAMETERS
STRUCTURE PROPERTIES
| Parameter | Material type (graded by main pore size range), μm | |||||
|---|---|---|---|---|---|---|
| 140-315 | 200-400 | 315-630 | 630-1000 | 1000-1600 | 1600-3000 | |
| Mean pore size, μm | 245 | 300 | 490 | 700 | 1300 | 2300 |
| Mean neck size, μm | 67…77 | 73…88 | 100…120 | 135…170 | 175…225 | 245…315 |
| Neck per one pore (coordination number) | 6.5 | 6.5 | 6.5 | 6.5 | 6.5 | 6.5 |
| Pores per unit area, pcs./ m² | 11.6×106 | 6.4×106 | 2.4×106 | 1.2×106 | 0.34×106 | 0.11×106 |
| Necks per unit area, pcs./ m² | 36.4×106 | 20.9×106 | 7.9×106 | 3.9×106 | 1.1×106 | 0.36×106 |
| Porosity, % | 50...75 | |||||
| Density***, kg/m³ | 675...1215 | |||||
| Thermal expansion coefficient, 1/°C | 23.0×10-6 (identical to solid metal) | |||||
| Allowed temperature range, °C | -200...+250 | |||||
More details on mechanical properties of ALUPOR™ see "Properties" page.
MECHANICAL PROPERTIES
| Parameter | Material type (graded by main pore size range), μm | |||||
|---|---|---|---|---|---|---|
| 140-315 | 200-400 | 315-630 | 630-1000 | 1000-1600 | 1600-3000 | |
| Ultimate compressive strength, MPa | 105 | 59 | 58 | 49 | 37 | 32 |
| Yield point at compression, MPa | 39 | 26 | 24 | 20 | 21 | 20 |
| Ultimate tensile strength, MPa | 29 | 16 | 16.5 | 14 | 12 | 8 |
| Yield point at tensile, MPa | 26 | 14 | 16 | 13 | 13 | 7 |
| Ultimate shear stress, MPa | 36 | 34 | 30 | 25 | 26 | - |
| Young's modulus, GPa | 3.1 | 2 | 1.9 | 1.7 | 1.7 | 1.6 |
| Elongation, % | 0.29 | 0.38 | 0.27 | 0.32 | 0.3 | 0.12 |
More details on mechanical properties of ALUPOR™ see "Properties" page.
MANUFACTURE ABILITIES
- Maximum dimensions of the final flat part: 850 × 650 × 150 mm
- Maximum dimensions of the cylinder part: ø410, length is not limited
- Minimum plate thickness:
- 3 mm for parts up to 300 mm
- 5 mm for parts up to 500 mm
- 8 mm for parts over 500 mm
- Final product weight: up to 150 kg
- Manufacturing method: casting with vacuum impregnation of NaCl (see here...)
- Threading available for both solid metal and porous sections
Parts with Solid Metal Sections (SMS) are a significant advantage of our technology because we can do fastening elements on solid section. Possible options for manufacturing parts with solid metal sections are presented below.
Without solid section
Solid end face
Solid flange
Seal slots for O-ring
Tread & Hex-nut
Tread & Seal slots
Modular Mufflers
The image shows a special solution for large-volume steam discharge: a steel casing containing a cylindrical porous element with anti-icing electric heating incide.
Anodizing and Oxidation
To enhance corrosion resistance it is possible to perform anodizing or micro-arc oxidation treatment on the entire internal surface of pores.
EU legislation reference
To protect workers from exposure to harmful noise and toxic substances levels, organizations and governments define standards for machine manufacturers. Pneumatic silencers are commonly certified to the following standards:
- Pressure Equipment Directive (PED) - Directive 2014/68/EC
- Restriction of Hazardous Substances (RoHs) - Directive 2002/95/EC
- Registration, Evaluation, Authorization and Restriction of Chemicals(REACH) - EC No 1907/2006
- Minimum health and safety requirements regarding the exposure of workers to the risks arising from physical agents (noise) - Directive 2003/10/EC
Noise and silencing standards
ISO 1999:2013 Acoustics — Estimation of noise-induced hearing loss
ISO 14163:1998 Acoustics — Guidelines for noise control by silencers
ISO 11820:1996 Acoustics — Measurements on silencers in situ
ISO 20145:2019 (Expected to be replaced by ISO/DIS 20145) Pneumatic fluid power — Test methods for measuring acoustic emission pressure levels of exhaust silencers
ISO 4871:1996 Acoustics — Declaration and verification of noise emission values of machinery and equipment
ISO 9053:1991 Acoustics - Materials for acoustical applications - Determination of airflow resistance
ISO 3740:2019 Acoustics — Determination of sound power levels of noise sources — Guidelines for the use of basic standards
ISO 9612:2009 Acoustics — Determination of occupational noise exposure — Engineering method
ISО 7235 Acoustics - Measurement procedures for dueled silencers-Insertion loss, flow noise and total pressure loss
ISO 6358-1:2013 Pneumatic fluid power — Determination of flow-rate characteristics of components using compressible fluids. Part 1: General rules and test methods for steady-state flow
ISO 6358-2:2019 Pneumatic fluid power — Determination of flow-rate characteristics of components using compressible fluids. Part 2: Alternative test methods
ISO 6358-3:2014 Pneumatic fluid power — Determination of flow-rate characteristics of components using compressible fluids. Part 3: Method for calculating steady-state flow-rate characteristics of systems